pad

pad 30 Reversible Ramp Plow

Easy Quick Attachment To Buckets On Front End Loaders!

This snow blade is designed for easy quick attachment directly to the buckets of front end loaders. After critical areas are cleaned and the snow and slush pushed away the blade can be removed from the bucket which then can be used for loading.

Due to its large size you reduce the clean up time substantially over conventional plows, loader buckets or dozers.

With the end plates attached, the reversible ramp plow is designed to push snow and slush away from terminal buildings, gates, ramp areas, and areas used for boarding and deplaning passengers.

Due to the size and easy maneuverability of the blade, critical and hard to get at areas can be quickly cleaned. Clean ramp areas increases the mobility of ground support equipment and positive traction for heavy airplane tugs.

Removing the end plates, either right end or left end, allows the reversible ramp plow to discharge snow in either direction. This enables windrows to be formed for blowers to remove or for loading in trucks. By removing both end plates the reversible ramp plow is designed for runway snow removal at moderate speeds.

Height: 53"
Thickness: 10 Ga.
Cutting Edge: (3) 1/2" x 6" x 10'
Inner Vertical Ribs: (11) 1/2" x 4"
End Vertical Ribs: (2) 3/4" x 4"
Rib Reinforcement Angle: (12) 3-1/2" x 3-1/2" x 1/2"
Top Angle: 4" x 3" x 3/8"
Bottom Angle: 4" x 4" x 3/4"
Bottom Angle Reinforcement Plate: (3) 1/2" x 3" x 120"
Bottom Angle Reinforcement Gussets: (27) 3/8" x 3 x 9"
Bottom Angle Reinforcement Boxed: 30' x 4" Ship Channel
Connecting Points: (22) 3" x 3" x 1/2" Angle
Connecting Bolts: (18) 3/4" x 2-1/2" Grd. 8
Back Reinforcement: 20 Ft.x 9" x 240" 15lb. channel
Semi-Circle
Front Tube: 8"x6" x 1/2W Tubing 240"
Top Plate: 1/2" x 48"x 85"
Lower Plate: 3/8" x 48" x 48"
Caster Brackets: (2) 4" x 4" x 48"
Power Reverse: (2) 4-1/2" x 421/2" Stroke with 1/2" ports
A-Frame
Top Plate: 3/8" x 46"
Center Stiffener: 1" x 5"
Back Plate: 1" x 6"
Holddown Plate: 3/4" x 14" x 41-1/2"
End Plates: (2) 1" x 49" x 57"
(2) Reinforcing Tubes
3" Black Pipe
Lift Bracket
Down Bracing: (2) 4" x 13.8 lb. Ship Channel
Pivot Plate: (1) 1" x 10"
Center Pin: (1) 2" dia. X 9-1/2"
Caster Assembly
Outer Barrel: (2) 6-1/4" O.D. X 1/2 W Tubing
Inner Barrel: (2) 5-1/8" O.D. X 1/2 W Tubing
Adjusting Screw: 1-1/2 dia. Stress proof
Caster: (2) 360 degree swivel tandem 6.90 x 9
10 ply with swivel restrictors




Root Spring Scraper Co.
527 W. North St.
Kalamazoo, MI 49007
269-382-2025
800-333-ROOT
269-382-5920 Fax
salesteam@rootsnowplows.com